All MOTOROLA Tricks And Hacks

Motorola Star Tac

Show IMEI code
If you need to know what’s the IMEI code of your phone,
simply press:
* # 06 #
you’ll read it on display.

Pin-Out

1) Connected with 22pf to pin 3
2) RF out
3) Connected with 33 pf to pin 8, 33 pf to pin, 33 pf to pin 7
4) BAT_FDBAK
5) MAN_TEST connected with 10k to L275
6) RS232_TX – connected to MCU SPI bus
7) RS232_RX – connected to MCU SPI bus
8) AUDIO_IN
9) AUDIO_OUT
10) Connected with 33 pf to pin 13, 33 pf to pin 14
11) UPLINK -|
12) DOWNLINK -|- DSC bus connected to the BIC
13) DSC_EN_B -|
14) EXT_B+
15) Gnd

Motorola mtac Elite

Show IMEI code

If you need to know what’s the IMEI code of your phone,
simply press:
* # 06 #
you’ll read it on display.

Test Mode

To enter in Nam programming Mode, press:
[arrow up]
000000000000 (12 times zero)
[MR]
now display shows the first step of NAM programming;
simply enter data and move to the next step using:
* (the same key of [left arrow])

Software version

To see software version of your phone you need to short-circuit antenna ground
with the two nearest pin together in the connector located under the phone. then:
Power ON the phone
and type:
#19#
now display is showing software version of your phone.

Serial Number

To see the serial number of your phone you need to short-circuit antenna ground
with the two nearest pin together in the connector located under the phone. then:

Power ON the phone

and type:

#75#
now display is showing the first pair of digits, then go ahead using

* (the same key of [left arrow])

to show the second pair and so on.

Pin Out

The pins are numbered 1 thru 10 from right to left
ANT- (O) | | | | | | | | | |

1) Audio Ground
2) Ext b+
3) T Data
4) C Data
5) R Data
6) Logic Ground
7) Audio Out – on/off
8) Audio In
9) Manual Test
10) Battery Feedback

Motorola Micro tac

Test Mode

To enter in Nam programming Mode,
you need to short-circuit the first and the third battery pin from the right, then:
Power ON the phone
display will show “Tacs5″, type in:
55
now display shows the first step of NAM programming;
simply enter data and move to the next step using:

* (the same key of [left arrow])

Software version

To enter in Nam programming Mode,
you need to short-circuit the first and the third battery pin from the right, then:
Power ON the phone
display will show “Tacs5″, type in:
19
now display is showing software version of your phone.

Motorola mtac Elite

Test Mode

To enter in Nam programming Mode, press:

[arrow up]
000000000000 (12 times zero)
[MR]

now display shows the first step of NAM programming;
simply enter data and move to the next step using:
* (the same key of [left arrow])

Software version

To see software version of your phone you need to short-circuit antenna ground with the two nearest pin together in the connector located under the phone. then:
Power ON the phone
and type:

#19#

now display is showing software version of your phone.

Serial Number

To see the serial number of your phone you need to short-circuit antenna ground with the two nearest pin together in the connector located under the phone. then:
Power ON the phone
and type:

#75#

now display is showing the first pair of digits, then go ahead using
* (the same key of [left arrow])

to show the second pair and so on.

Pin Out

The pins are numbered 1 thru 10 from right to left

ANT- (O) | | | | | | | | | |

1) Audio Ground
2) Ext b+
3) T Data
4) C Data
5) R Data
6) Logic Ground
7) Audio Out – on/off
8) Audio In
9) Manual Test
10) Battery Feedback

Motorola 8700

Show IMEI code

If you need to know what’s the IMEI code of your phone,
simply press:

* # 06 #

you’ll read it on display.

Turn on Clock

To turn on the hidden clock on your phone follow the following procedure:
In Setup menu turn ON “extended menu”
in language selection change to “GREEK” or “EAAKA”
exit menu
press key labeled “i” (the info key)
type *#25625# and finally
turn OFF the phone
next time you’ll wake up the phone the clock will be on your display and while surfing menu you’ll find the option to set its time.

RBS Info

To activate RBS info menu simply press:
[][][]113[]1[]OK (“[]” = the block you obtain pressing “*” for 3 seconds or more)
this procedure seems not to work on all software version but it’s the only one you can try from keypad.

Software Bug

Some 8700 remain frozen after you switched on cell broadcast; the phone seems to function properly but it can’t origin or receive any calls and turns off when you press any key.

About these ads

One Response

  1. please send me the tricks of mobile free accesses

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

Follow

Get every new post delivered to your Inbox.

Join 43 other followers

%d bloggers like this: